ISO INTERNATIONAL STANDARD 13628-10 First edition 2005-10-01 Petroleum and natural gas industries- Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe Industries du pétrole et du gaz naturelConception et exploitation des systemesdeproductionimmerges Partie 10:Specification pour canalisations flexibles composites Referencenumber ISO 13628-10:2005(E) IS ISO2005 Copyight Intemaltional Organization for Standardizatior J by IHS thout license from IHS Not for Resale ISO13628-10:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsiblity of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISo member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2005 A ights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISo at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56-CH-1211 Geneva 20 Tel.+41227490111 Fax +41227490947 E-mail [email protected] Web www.iso.org Published in Switzerland Copyight tematinal Orgarizaion for Sandardizatin OISO 2005-Allr rights reserved Not for Resale ISO 13628-10:2005(E) Contents Page Foreword, Introduction.. 1 Scope 1.1 Purpose. .. 1.2 Products 1.3 Application 2 Normative references 3 Terms,definitionsandabbreviation 3.1 Terms and definitions 3.2 Symbols andabbreviation 4 Functional requirement 4.1 General . 4.2 Overall requirements.. 4.3 General designparameters 12 4.4 Internal fluid parameter 4.5 External environment. 14 4.6 System requirements 14 5 Design requirements 5.1 Loadsand loadeffects. 17 5.2 Pipe design methodolog .. 20 5.3 Pipe structure design... 21 5.4 System design requirements .26 .29 6 6.1 Material requirements. 29 6.2 Qualification requirement 6.3 Quality assurance requirements 7 Manufacturing requirements 41 Qualityassurance requirements 41 7.1 7.2 Carcas..... 7.3 Preparation of compound and calendering 43 7.4 Elastomer winding ........ 4 7.5 Reinforcement armourlayer. 45 7.6 Insulation layers... 45 7.7 End fitting 45 7.8 Curing process. 7.9 Special processes 48 7.10 Manufacturing tolerances 50 7.11 Repairs 50 8 Documenta. tio. n 51 8:2 5 8.3 Design load repor 51 8.4 5 8.5 Manufacturing quality plan 52 8.6 Fabrication specification 52 8.7 As-built documentation. 52 8.8 Operation manual 53 Copyright Interational Organization orsfandardization ghts reserved ili e withISO. thoutlicense from IHS Nofor Resalke ISO 13628-10:2005(E) 9 Factoryacceptance...tes.ts. 9.1 General. 54 9.2 Gaugetes 5 9.3 Hydrostatic pressuretes 9.4 Electrical continuity and resistance tests 9.5 Kerosenetest. 9.6 Vacuumtest 56 10 Marking and packaging. .57 10.1 Marking.... 10.2 Packaging .57 Annex A(informative) Purchasing guideline. 59 Annex B(informative) Bend stiffenersand bend restrictor.. 6 Annex C(informative) Useof theAPI Monogram 71 Bibliograph. ISO 2005-All rights reserved Copyight Intemational Organization forStandardization byIHS under Notfor Resale 13628-10:2005(E) ISO Foreword IsO(the International Organization for Standardization)is a worldwide federation of national standards bodies (IsO member bodies).The